CipherLab 1502 Podręcznik Użytkownika Strona 24
- Strona / 150
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
14
Enter Setup
1500/1502 Barcode Scanner User Guide
1.3 LED INDICATOR
The dual-color LED on top of the scanner is used to provide user feedback. For example,
the LED becomes solid red and goes off quickly (= Standby mode) upon powering on or
running out of transmit buffer. You may tell the difference by the beeps – for example,
you will hear a long beep of high tone when powering on the scanner, and a long beep of
low tone when the transmit buffer becomes full.
LED – Red/Green
Meaning
Red, and goes off quickly
Power on, with one long beep (high tone)
Transmit buffer full, with one long beep (low tone)
RS-232 connection fails, with two beeps (high-low tone)
Green, and goes off quickly Good Read, with one short beep (high tone) and beeper pitch
and duration programmable
Flashing red Configuration Mode
1.3.1 GOOD READ LED
1.3.2 GOOD READ LED DURATION
By default, the Good Read LED stays on for 40 milliseconds. Specify a value, ranging
from 1 to 254 in units of 10 milliseconds.
1) Read the label above to specify the time interval before the Good Read LED goes off.
*Enable Good Read LED
D
isable Good Read LED
Good Read LED Time-Out after
0.01~2.54 seconds (*40 ms)
- 1500/1502 Barcode Scanne 1
- IMPORTANT NOTICES 3
- RELEASE NOTES 5
- CONTENTS 7
- INTRODUCTION 11
- Enter Setup 12
- QUICK START 13
- ENTER CONFIGURATION MODE 14
- EXIT CONFIGURATION MODE 14
- Refer to Appendix III 19
- LIST THE CURRENT SETTINGS 20
- Chapter 1 23
- Beeping 26
- Meaning 26
- 1.4.2 GOOD READ BEEP 27
- 1.5 SEND “NR” TO HOST 28
- 1.6 SCAN MODES 29
- 1.6.1 CONTINUOUS MODE 30
- 1.6.5 AUTO POWER OFF MODE 32
- 1.6.6 AIMING MODE 32
- 1.6.7 MULTI-BARCODE MODE 33
- 1.6.8 ALTERNATE MODE 33
- 1.8 DELAY BETWEEN RE-READ 35
- Continuous mode 35
- Auto Power Off mode 35
- Alternate mode 35
- 1.9 EFFECTIVE DECODING AREA 36
- 1.9.1 POSITIONING WINDOW 36
- 1.9.2 ADJUSTING WINDOW 36
- Percentage for Right Half 37
- 1.11 NEGATIVE BARCODES 39
- 1.12 SYMBOLOGIES SUPPORTED 39
- Chapter 2 43
- 2.1 KEYBOARD WEDGE 44
- 2.1.2 KEYBOARD SETTINGS 45
- Alphabets Transmission 49
- Digits Transmission 49
- ALT Composing 50
- Laptop Support 50
- 2.1.3 INTER-CHARACTER DELAY 51
- 2.1.4 INTER-FUNCTION DELAY 51
- 2.2 RS-232 52
- 2.2.2 BAUD RATE 52
- 2.2.3 DATA BITS 53
- 2.2.4 PARITY 53
- 2.2.5 STOP BIT 54
- 2.2.6 FLOW CONTROL 54
- 2.2.7 INTER-CHARACTER DELAY 55
- 2.2.8 INTER-FUNCTION DELAY 55
- 2.2.9 ACK/NAK TIMEOUT 56
- 2.3 WAND EMULATION 57
- 2.3.2 NORMAL STATE 57
- 2.3.3 BAR STATE 57
- 2.3.4 MODULE TIME 58
- 2.3.5 MARGIN TIME 59
- Chapter 3 61
- 3.1 CODABAR 62
- 3.1.3 CLSI CONVERSION 63
- 3.2 CODE 25 – INDUSTRIAL 25 64
- 3.2.2 CHECKSUM VERIFICATION 65
- 3.2.3 CHECKSUM TRANSMISSION 65
- 3.3 CODE 25 – INTERLEAVED 25 67
- 3.3.2 CHECKSUM VERIFICATION 68
- 3.3.3 CHECKSUM TRANSMISSION 68
- 3.4 CODE 25 – MATRIX 25 70
- 3.4.2 CHECKSUM VERIFICATION 71
- 3.4.3 CHECKSUM TRANSMISSION 71
- 3.5 CODE 39 73
- 3.5.2 CHECKSUM VERIFICATION 73
- 3.5.3 CHECKSUM TRANSMISSION 74
- 3.6 CODE 93 75
- 3.7 CODE 128 75
- 3.8 EAN-8 76
- 3.8.1 CONVERT TO EAN-13 77
- 3.8.2 CHECKSUM TRANSMISSION 77
- 3.9 EAN-13 78
- 3.9.1 ISBN CONVERSION 79
- 3.9.2 ISSN CONVERSION 79
- 3.9.3 CHECKSUM TRANSMISSION 79
- 3.10 EAN-128 80
- 3.10.1 CODE ID TRANSMISSION 80
- 3.11 ISBT 128 81
- 3.12 MSI 82
- 3.12.1 CHECKSUM VERIFICATION 82
- 3.12.2 CHECKSUM TRANSMISSION 83
- 3.13 FRENCH PHARMACODE 85
- 3.13.1 CHECKSUM TRANSMISSION 85
- 3.14 ITALIAN PHARMACODE 86
- 3.14.1 CHECKSUM TRANSMISSION 86
- 3.15 PLESSEY 87
- 3.15.1 CONVERT TO UK PLESSEY 87
- 3.15.2 CHECKSUM TRANSMISSION 87
- 3.16 RSS FAMILY 88
- 3.16.1 CODE ID SELECTION 88
- 3.16.2 RSS-14 88
- 3.16.3 RSS EXPANDED 89
- 3.16.4 RSS LIMITED 90
- Application ID Transmission 91
- Checksum Transmission 91
- 3.17 TELEPEN 92
- 3.18 UPC-A 93
- 3.18.1 CONVERT TO EAN-13 94
- 3.18.3 CHECKSUM TRANSMISSION 94
- 3.19 UPC-E 95
- 3.19.4 CHECKSUM TRANSMISSION 97
- Chapter 4 99
- 4.2 CHARACTER SUBSTITUTION 100
- 4.4.2 CHANGE CODE ID 108
- 4.4.3 CLEAR CODE ID SETTINGS 110
- 4.5 LENGTH CODE 111
- 4.6 MULTI-BARCODE EDITOR 114
- Code Type 114
- Chapter 5 117
- 5.1 FORMAT SELECTION 118
- 5.1.2 EXCLUSIVE DATA EDITING 119
- 5.2 EDITING FORMAT 120
- 5.2.2 RESTORE DEFAULT FORMAT 122
- 5.2.3 DEFINE DATA CRITERIA 123
- 115 125
- Start Position 126
- Field Adjustment 126
- Total Number of Fields 126
- 5.2.5 FIELD SETTINGS 128
- 119 129
- Field 2 Setting 129
- Field 3 Setting 130
- 121 131
- Field 4 Setting 131
- Field 5 Setting 132
- 125 135
- 5.3 PROGRAMMING EXAMPLES 136
- 5.3.1 EXAMPLE I 136
- 127 137
- SPECIFICATIONS 139
- Programming Support 140
- Appendix I 141
- Appendix II 143
- Remarks 144
- Appendix III 145
- KEY STATUS 146
- USER-DEFINED SCAN CODE 146
- Appendix IV 147
- HEXADECIMAL SYSTEM 148
- ASCII TABLE 149
Powiązane produkty i podręczniki dla Czytniki kodów kreskowych CipherLab 1502
(217 strony)
(277 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.018 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji